Manufacturer catalog record · independently reviewed

HALO Acid Neutralizer

Manufacturer-listed well-water / specialty treatment record in the Acid Neutralizer family.

Well-water / specialty treatmentEvidence still partialNot current inventory
HALO brand mark; exact Acid Neutralizer product photography is not verified
Brand reference image only. Exact model photography has not been verified.

Buyer and owner guide · reviewed Oct 15, 2026

At a glance: HALO Acid Neutralizer is a backwashing calcite tank that raises the pH of acidic water, usually from a private well. The calcite dissolves as it works, so the media must be topped up and the water gets harder. It needs a drain and a 120 V outlet, and its documents disagree on some operating details.

Water System Guide is an independent research publisher. This model-specific document review was completed October 15, 2026. It is not a household performance test, installer quote or confirmation of current warranty, stock or certification records.

How the calcite neutralizer works

The Acid Neutralizer product page describes calcite: crushed and screened white marble (calcium carbonate). Acidic water dissolves it slowly, which raises the pH and reduces leaching of copper, lead and other metals from plumbing. HALO calls calcite self-limiting: when properly applied, it corrects pH only to a non-corrosive equilibrium and does not over-correct under normal conditions.

The same page notes the trade-off. As calcite dissolves it increases hardness, and HALO says a CK10 softener may become necessary after the neutralizer. Test hardness as well as pH after installation.

H-AN-100 media specifications

The Acid Neutralizer specification table for H-AN-100 lists calcite with a 6 gpm per cubic foot service flow, 50% freeboard, 12–15 gpm per square foot backwash rate at 60 °F, a 24-inch minimum bed depth, 12 × 40 screen size and 90 lb per cubic foot bulk density. It lists a pH range of 5.0–6.0, while a bullet on the same sheet says it is effective from 5.0 to 7.0 pH.

The sheet does not state the tank size or media volume, so household flow cannot be worked out from the per-cubic-foot rate. Ask the seller for the media volume and the resulting service flow, and match the pH range to your test result.

Drain, power and pressure requirements

The installation manual, page 3 lists a 25–80 psi pressure range, with about 60 psi recommended. The drain outlet is a 3/4-inch threaded fitting; the drain line is pressurized and can run slightly uphill. The valve needs a non-switched, grounded 120 V outlet and comes with a 15-foot cord. The unit must never freeze. In moderate climates it may go outdoors, or be buried with at least 6 inches of clearance below the control valve.

The specification warning limits use to cold water at no more than 80 psi, at 40–100 °F, and excludes microbiologically unsafe water without adequate disinfection.

Startup and media top-ups

The installation manual, page 6 sets backwash ('regeneration') to every 3 days and calls for two forced regenerations at startup, followed by running every fixture. Skipping them may leave milky water. The manual's introduction, on page 3, instead says the unit regenerates for ten minutes each day. Confirm the setting the installer programs.

The manual, page 7 says the media is sacrificial and must be added periodically, with the media level checked every six months. The warranty goes further: media "must be replace annually as it is a consumable". Budget for media at least once a year, and check the level at six months.

Warranty: valve, electronics and tank

The Acid Neutralizer limited warranty covers valve and electronics parts for five years from the manufacture date shown by the serial number, or from a documented purchase or installation date. It provides one replacement tank within ten years. Media is not warranted. Media and internal valve parts are excluded when the system is used to remove iron or manganese, or with very high chlorine.

Coverage requires 33–120 °F water and 40–80 psi, and the system must never freeze. Installation workmanship, vacuum damage and unsupported plumbing are not covered. The warranty does not transfer to a later owner.

Frequently asked questions

Does the HALO Acid Neutralizer make water harder?

Yes. The calcite dissolves into the water as it raises pH, which increases hardness. HALO says a CK10 softener may become necessary after the neutralizer.

What pH does the HALO Acid Neutralizer treat?

The H-AN-100 specification table lists a 5.0–6.0 pH range, while a bullet on the same sheet says it is effective from 5.0 to 7.0. Match this to a current water test, and ask the seller which range applies.

How often does the calcite need to be replaced?

The manual says to check the media level every six months and add media as needed. The warranty says media must be replaced annually as a consumable.

Does the HALO Acid Neutralizer need electricity and a drain?

Yes. The control valve needs a non-switched, grounded 120 V outlet, and the unit backwashes to a drain through a 3/4-inch fitting.

Sources for this model guide

  1. HALO Acid Neutralizer manufacturer specification — 10-2-24 filename; copyright 2024 in document; reviewed 2026-10-15.
  2. HALO Acid Neutralizer manufacturer installation manual — Document 68110751 filename; undated body; reviewed 2026-10-15.
  3. HALO Acid Neutralizer manufacturer limited warranty — 2126.2 filename; undated body; reviewed 2026-10-15.
  4. HALO Acid Neutralizer manufacturer product page — Undated current product page; reviewed 2026-10-15.

Known product details

Manufacturer
HALO
Model or family
Acid Neutralizer
Catalog name
Acid Neutralizer
Product category
Well-water / specialty treatment
Product family
Acid Neutralizer
Historical equipment price
No current verified price; equipment and installed-scope pricing require current confirmation.
Source reviewed
2026-08-16

Evidence and source boundary

Price and availability notes are historical source records, not live offers or stock checks. After any stated verification expiry, obtain a new seller check before relying on the value.

Manufacturer catalog presence was observed in the pinned source workbook. Current stock, dealer authorization, installation scheduling, and address-level service are not verified.

The controlling source for this catalog observation is halowater.com, reviewed on 2026-08-16. A manufacturer page may change, redirect, or describe a family rather than every configuration; compare the exact current documentation before purchase.

What still needs confirmation

  • Certification: verify the exact model number, contaminant or reduction claim, standard, listing scope, and current certificate.
  • Sizing: match household demand, flow, plumbing, pressure, water chemistry, and waste/discharge requirements.
  • Ownership: confirm current equipment price, installation scope, consumables, maintenance intervals, warranty conditions, and service access.
  • Availability: manufacturer catalog presence does not establish current stock, dealer authorization, installer capability, or local availability.

How to use this record

  1. Copy the exact model or family name shown above.
  2. Open the cited manufacturer source and confirm that the current page still matches.
  3. Request the current model-specific specification sheet, certification listing, warranty, and installed-scope quote.
  4. Use water evidence and site constraints before comparing this product with alternatives.