Manufacturer catalog record · independently reviewed

HALO H2Z1054-SM-100

Manufacturer-listed salt-free conditioner record in the H2 ZERO Scale Media family.

Salt-free conditionerEvidence still partialNot current inventory
HALO H2Z1054-SM-100
Product image associated with the cited manufacturer record.

Buyer and owner guide · reviewed Oct 15, 2026

At a glance: HALO H2Z1054-SM-100 is the salt-free scale media tank in the H2 Zero carbon / scale media system. It conditions hardness minerals without salt, drain or electricity, but it does not remove them. Its feed-water limits are strict, and the published scale-media warranty terms disagree with each other.

Water System Guide is an independent research publisher. This model-specific document review was completed October 15, 2026. It is not a household performance test, installer quote or confirmation of current warranty, stock or certification records.

Where H2Z1054-SM-100 fits in the H2 Zero system

The H2 Zero product page offers two layouts: carbon with the HALO ION, or carbon with HALO proprietary scale media (no salt). The specification, page 1 shows the carbon / scale media arrangement as two tanks labeled H2Z1054-CPSM-100 (1"). Its dimension table on page 2 lists H2Z1054-SM-100 on its own. Treat SM-100 as the scale media tank, and confirm on the quote whether the carbon tank is included.

Scale media conditions water instead of exchanging ions. Hardness stays in the water, so a hardness test will not drop after installation. If you need measured hardness removal, that calls for a softener, not this tank.

Published H2Z1054-SM-100 specifications

The H2 Zero specification, page 2 lists H2Z1054-SM-100 with a 0.75–1 inch main size, 10 gpm service flow, 15 gpm peak flow, 15–80 psi and 40–110 °F. Its dimensions are 45 lb ship weight and 12 × 12 × 59 inches (length, width, height).

Those figures describe the tank in the table. The complete installation also needs room for the carbon tank, a bypass, a downstream Sediment Guard, a hose bib and a ball valve, as shown in the diagram on the specification's first page.

Feed-water limits that protect the scale media

The scale media manual, page 5 sets limits of iron 0.3 ppm, manganese 0.05 ppm, copper 1.3 ppm, pH 6.5–8.5 and free chlorine below 2 ppm. It warns that iron and manganese can coat the media and reduce its effectiveness. No hydrogen sulfide can be present, because the media turns gray and stops working. The media does not reduce silica scaling.

New copper lines must be passivated for at least 4 weeks before the scale media goes into service; the carbon can run alone during that time. The manual lists 15–90 psi and 40–100 °F, while the specification sheet caps pressure at 80 psi and lists 110 °F. Plan to the narrower range: 15–80 psi and 40–100 °F. HALO requires a well-water analysis before any well installation.

Soak, flush and filter before water enters the home

The scale media manual, page 6 requires a 48-hour carbon soak, then repeated 5-minute flushes with 2-minute rests, at least six times, until the water runs clear of carbon fines. The specification sheet gives a 24-hour minimum, so follow the longer manual figure.

The included Sediment Guard must go after the system. It filters to 5 microns and is not a substitute for soaking and flushing. The manual says to replace its filter yearly. The specification adds that conditioning results may vary above 25 grains per gallon.

Resolve the scale media warranty conflict in writing

The product page and the specification, page 2 advertise a 10-year carbon and 5-year scale warranty for the scale media option. The carbon / scale media warranty document instead says that scale media is consumable and therefore not under warranty. It does cover one replacement tank for a defect, 10 years of control-valve parts and 10 years of replacement carbon media for media failure.

The same warranty requires 40–80 psi regulated pressure, 33–110 °F water, influent chlorine no higher than 1 mg/L, a licensed contractor install and purchase through authorized distribution. Ask the seller which scale media terms apply to your purchase, and get the answer in writing.

Frequently asked questions

Does H2Z1054-SM-100 remove hardness?

No. It is a salt-free scale media conditioner. Hardness minerals stay in the water, so a hardness test will not drop. Hardness removal needs an ion-exchange softener.

What flow rate does HALO publish for H2Z1054-SM-100?

The specification lists 10 gpm service flow and 15 gpm peak flow for the 0.75–1 inch main size, at 15–80 psi.

Can H2Z1054-SM-100 go on new copper plumbing?

The manual says new copper lines must be passivated for at least 4 weeks before the scale media goes into service. The carbon stage can run alone during that time.

Is the H2 Zero scale media under warranty?

HALO's sources disagree. The product page and specification show a 5-year scale warranty, but the warranty document says scale media is consumable and not covered. Confirm the terms in writing before purchase.

Sources for this model guide

  1. HALO H2 Zero Carbon / Scale Media manufacturer specification — Rev.3326 filename; reviewed 2026-10-15.
  2. HALO H2 Zero Scale Media manufacturer installation manual — Document 68111025, Rev.3326 filename; reviewed 2026-10-15.
  3. HALO H2 Zero carbon / scale media manufacturer warranty — Rev.3326 filename; copyright 2024 in document; reviewed 2026-10-15.
  4. HALO H2 Zero Scale Media manufacturer product page — Undated current product page; reviewed 2026-10-15.

Known product details

Manufacturer
HALO
Model or family
H2Z1054-SM-100
Catalog name
H2 ZERO Scale Media H2Z1054-SM-100
Product category
Salt-free conditioner
Product family
H2 ZERO Scale Media
Historical equipment price
No current verified price; equipment and installed-scope pricing require current confirmation.
Source reviewed
2026-08-16

Evidence and source boundary

Price and availability notes are historical source records, not live offers or stock checks. After any stated verification expiry, obtain a new seller check before relying on the value.

Manufacturer catalog presence was observed in the pinned source workbook. Current stock, dealer authorization, installation scheduling, and address-level service are not verified.

The controlling source for this catalog observation is halowater.com, reviewed on 2026-08-16. A manufacturer page may change, redirect, or describe a family rather than every configuration; compare the exact current documentation before purchase.

What still needs confirmation

  • Certification: verify the exact model number, contaminant or reduction claim, standard, listing scope, and current certificate.
  • Sizing: match household demand, flow, plumbing, pressure, water chemistry, and waste/discharge requirements.
  • Ownership: confirm current equipment price, installation scope, consumables, maintenance intervals, warranty conditions, and service access.
  • Availability: manufacturer catalog presence does not establish current stock, dealer authorization, installer capability, or local availability.

How to use this record

  1. Copy the exact model or family name shown above.
  2. Open the cited manufacturer source and confirm that the current page still matches.
  3. Request the current model-specific specification sheet, certification listing, warranty, and installed-scope quote.
  4. Use water evidence and site constraints before comparing this product with alternatives.