Buyer and owner guide · reviewed Oct 8, 2026
At a glance: The H-CK10-250 is the largest CK10: a 13 x 54-inch mineral tank, 2.5 of resin, the same 18 x 36-inch brine tank as the smaller sizes and an 18 gpm peak flow. HALO publishes no grain rating. The installer's capacity and salt settings, and a drain line sized for the backwash, decide how it runs.
Water System Guide is an independent research publisher. This model-specific document review was completed October 8, 2026. It is not a household performance test, installer quote or confirmation of current warranty, stock, price or certification records.
The CK10-250 specification
HALO's CK10 spec sheet (December 2024) lists the H-CK10-250 with a 13 x 54-inch mineral tank, 2.5 in the resin column, an 18 x 36-inch brine tank and an 18 gpm peak flow, the highest of the three CK10 sizes. The series includes a high-flow bypass and 1-inch plastic elbow connectors.
The sheet heads the resin column "SQ FT". Resin is measured by volume, so confirm with the installer that the tank holds 2.5 cubic feet. The CK10-200 (12 x 52 inches, 2, 16 gpm) uses the same brine tank. See CK10-150 vs 200 vs 250.
Estimating its grain capacity
HALO publishes no grain rating for the CK10-250. The CK10 operating manual, page 5, gives general exchange data of about 20,000 grains per cubic foot alongside 6 pounds of salt and about 25,000 alongside 8 pounds. By our arithmetic, 2.5 cubic feet works out to roughly 50,000–62,500 grains. That is an estimate, not a HALO rating.
The value that governs regeneration is the exchange capacity the installer enters in the OEM set-up, with pounds of salt per regeneration (manual, page 12). A larger softener programmed with a high salt dose can use more salt than a smaller one. Ask for both settings in writing.
Drain line and valve ratings
The manual calls for a drain line of at least ½ inch, and a ¾-inch line where the backwash flow rate exceeds 7 gpm or the line runs longer than 20 feet (page 3). It does not list a backwash rate for each CK10 size, so ask the installer what backwash rate and drain line flow control the CK10-250 will use and size the drain to match.
The control valve is rated for 27 gpm service flow at a 15 psi drop (page 4). That is the valve's rating, not the softener's. Use HALO's 18 gpm model figure when comparing with your home's peak demand.
Homes, light commercial and the residential warning
The CK10 spec sheet describes the series as ideal for most homes or light commercial applications. The warning on the same sheet says the CK10 is intended for residential use only, for cold water, at no more than 80 psi and 40–100°F, and must not freeze.
The CK10 warranty (July 2025) does not transfer to a later owner and excludes labor. If a CK10-250 is proposed for anything other than a single home, ask HALO in writing whether the warranty applies to that use.
Warranty: pretreatment matters
HALO's CK10 warranty gives the valve and electronics 5 years and one replacement tank within 10 years of purchase, with 1 year on resin. The valve and resin terms extend to 10 years when a HALO 5, H2 Zero or Mini system pretreats the CK10. Media and internal valve parts are not covered on feed water at or above 1 ppm chlorine, and the warranty requires 33–120°F and 40–80 psi.
Keep the serial number and proof of purchase or installation date, since the valve term runs from the manufacture date shown by the serial number unless a purchase or installation date is proven. See our HALO warranty guide and CK10 settings guide.
Frequently asked questions
How many grains is a HALO CK10-250?
HALO does not publish a grain rating. Using the CK10 manual's exchange data of about 20,000 to 25,000 grains per cubic foot, 2.5 cubic feet of resin works out to roughly 50,000 to 62,500 grains. That is an estimate, not a HALO rating.
What is the peak flow of the HALO CK10-250?
HALO's December 2024 spec sheet lists an 18 gpm peak flow for the H-CK10-250, compared with 16 gpm for the CK10-200 and 14 gpm for the CK10-150.
What size drain line does a CK10-250 need?
The CK10 manual calls for at least a ½-inch drain line, and a ¾-inch line if the backwash flow exceeds 7 gpm or the line is longer than 20 feet. Ask the installer for the backwash rate.
Is the CK10-250 resin warranty 10 years?
Only with HALO pretreatment. The July 2025 CK10 warranty covers resin for 1 year, extended to 10 years when a HALO 5, H2 Zero or Mini system pretreats the softener.
Related guides
Sources for this model guide
- HALO CK10 spec sheet — Dated 12-5-24 in filename; copyright 2024; reviewed 2026-10-08.
- CK10 operating manual and programming guide posted by HALO — Uploaded November 2024; no HALO revision in document; reviewed 2026-10-08.
- HALO CK10 softening system limited warranty — Dated 7-13-25 in filename; reviewed 2026-10-08.
Known product details
- Manufacturer
- HALO
- Model or family
- H-CK10-250
- Catalog name
- HALO CK10 Softener H-CK10-250
- Product category
- Water softener
- Product family
- CK10
- Water-source fit
- City water, Well water
- Historical equipment price
- No current verified price; equipment and installed-scope pricing require current confirmation.
- Source reviewed
- 2026-08-16
Evidence and source boundary
Price and availability notes are historical source records, not live offers or stock checks. After any stated verification expiry, obtain a new seller check before relying on the value.
Manufacturer catalog presence was observed in the pinned source workbook. Current stock, dealer authorization, installation scheduling, and address-level service are not verified.
The controlling source for this catalog observation is halowater.com, reviewed on 2026-08-16. A manufacturer page may change, redirect, or describe a family rather than every configuration; compare the exact current documentation before purchase.
What still needs confirmation
- Certification: verify the exact model number, contaminant or reduction claim, standard, listing scope, and current certificate.
- Sizing: match household demand, flow, plumbing, pressure, water chemistry, and waste/discharge requirements.
- Ownership: confirm current equipment price, installation scope, consumables, maintenance intervals, warranty conditions, and service access.
- Availability: manufacturer catalog presence does not establish current stock, dealer authorization, installer capability, or local availability.
How to use this record
- Copy the exact model or family name shown above.
- Open the cited manufacturer source and confirm that the current page still matches.
- Request the current model-specific specification sheet, certification listing, warranty, and installed-scope quote.
- Use water evidence and site constraints before comparing this product with alternatives.
